![]() The accessory battery, and possibly also a bow thruster and other batteries are each connected to the starter battery with Cyrix battery combiners. In a typical setup the alternator is directly connected to the starter battery. The main feature is that there is virtually no voltage loss so that the output voltage of alternators or battery chargers does not need to be increased. The Cyrix-ct 12/24 automatically detects system voltage.Ĭyrix battery combiners are an excellent replacement for diode isolators. LED 0,25 s blink: alarm (over temperature voltage > 16 V both batteries < 10 V one battery < 2 V) (multiply by two for 24 V) LED 2 s flash: connecting LED 2 s blink: disconnecting LED on: engaged LED 10 s flash: disengaged LED status indication (Cyrix 12/24 230 only) The Cyrix will disengage in case of excessive contact temperature, and reengage again after it has cooled down. Protection against overheating (due to a long duration overload e.g.) Long bolts to allow connection of more than one power cableĬyrix 12/24-120: 13 mm (M6) Cyrix 12/24-230: 16 mm (M8) (for Battery Combiners with multiple engage/disengage profiles, please see the Cyrix-i 400) The time delay depends on the voltage deviation from the trend. The Cyrix-ct 12/24 looks at the general trend (voltage increasing or decreasing) and reverses a previous action only if the trend has reversed during a certain period of time. The software of the Cyrix-ct 12/24 does more than simply connect and disconnect based on battery voltage and with a fixed time delay. A battery combiner also may fail to connect a large but discharged battery bank because the DC voltage immediately drops below the disengage value once the batteries are connected. Some battery combiners (also called voltage controlled relay, or split charge relay) will disconnect a battery in case of a short but high amperage load. Intelligent battery monitoring to prevent unwanted switching The load will be reconnected 30 seconds after the battery voltage has increased to more than the preset reconnect voltage. If the battery voltage increases again to the connect threshold within this time period (after the engine has been started for example), the load will not be disconnected. The load will be disconnected 90 seconds after the battery voltage drops below the preset level. The alarm output is typically used to activate a buzzer, LED or relay.ĭelayed load disconnect and delayed reconnect The alarm output is a short circuit proof open collector output to the negative (minus) rail, max. Starting the engine will therefore not activate the alarm. The alarm output is activated if the battery voltage drops below the preset disconnect level during more than 12 seconds. No relays but MOSFET switches, and therefore no sparks. ![]() To prevent damage to sensitive loads due to over voltage, the load is disconnected whenever the DC voltage exceeds 16.3V respectively 32.6V. This is important in case of Li-ion batteries, especially after low voltage shutdown. Note: the BatteryProtect can also be used as a charge interrupter in between a battery charger and a Li-ion battery. In this mode the BatteryProtect can be controlled by the VE.Bus BMS. Alternatively, one of nine predefined engage/disengage levels can be set with the programming pin (see manual). When using Bluetooth to program the Smart BatteryProtect any required engage/disengage levels can be set. The Smart BatteryProtect automatically detects system voltage one time only. The on/off input can be used as a system on/off switch. The Smart BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine. ![]() Protects the battery against excessive discharge and can be used as a system on/off switch Two groups of Products in this section 1. Power Packs for 400V High Energy Density Marine.Power Packs suit Caravans Outside Locker Fitment.Portable 240V Power & Lithium in a Case.Black Tie Cases with Inverter & 240V Power.Power Packs To Suit Iveco Daily and 4x4.Power Packs to Suit VW Crafter and MAN TGE. ![]() Power Packs to Suit Silverado/Denali/GMC.Power Packs to suit Dodge RAM 1500/ 2500.Power Packs to Suit Ford Ranger - Mazda BT50.Power Packs to Suit Toyota Landcruisers.AGM or Lithium Start & Lithium Auxiliary - Inverter Ready.AGM or Lithium Start & Lithium Auxiliary - No Inverter.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |